Micro-duct Connectors and End Plugs

 

Micro-duct Connectors - High Grade, Straight

HMPB30601

Description
The ”Crystal Clear” range of connectors are high grade connectors that offer reliable performance in all environments. The connectors are 100% metal-free and can be used directly into ground with salt water. The connectors are also highly resistant to chemicals, oil, gasoline etc. A crystal clear body facilitates fault location during installation. The connectors are available as straight connectors for spicing of micro-ducts with the same dimensions, or as reducers for splicing of ducts with different dimensions, as well as end stops for terminating duct ends to avoid water and dirt from entering the duct. The connectors can be installed directly into ground or above ground without additional protection.

 

Technical Information
Design: Micro-duct Connector and End Stops, re-openable
Type: Direct buried, Above ground use or in closurses, metal-free, chemical resistant
Dimensions: OD/ID Ø3/2 to 20/16 mm

Micro-duct Connectors – High Grade, Reduction Connectors

HMPB30603

Description

The ”Crystal Clear” range of connectors are high grade connectors that offer reliable performance in all environments. The connectors are 100% metal-free and can be used directly into ground with salt water. The connectors are also highly resistant to chemicals, oil, gasoline etc. A crystal clear body facilitates fault location during installation. The connectors are available as straight connectors for spicing of micro-ducts with the same dimensions, or as reducers for splicing of ducts with different dimensions, as well as end stops for terminating duct ends to avoid water and dirt from entering the duct. The connectors can be installed directly into ground or above ground without additional protection.

 

Technical Information
Design: Micro-duct Connector and End Stops, re-openable
Type: Direct buried, Above ground use or in closurses, metal-free, chemical resistant
Dimensions: OD/ID Ø3/2 to 16/12 mm

Micro-duct End Stop – High Grade

HMPB30606

Description

The ”Crystal Clear” range of connectors are high grade connectors that offer reliable performance in all environments. The connectors are 100% metal-free and can be used directly into ground with salt water. The connectors are also highly resistant to chemicals, oil, gasoline etc. A crystal clear body facilitates fault location during installation. The connectors are available as straight connectors for spicing of micro-ducts with the same dimensions, or as reducers for splicing of ducts with different dimensions, as well as end stops for terminating duct ends to avoid water and dirt from entering the duct. The connectors can be installed directly into ground or above ground without additional protection.

 

Technical Information
Design: Micro-duct Connector and End Stops, re-openable
Type: Direct buried, Above ground use or in closurses, metal-free, chemical resistant
Dimensions: OD Ø3 to 20 mm

Micro-duct Connectors – Gas Block, Straight

MPB 306 02 and MPB 306 07+

Description

The gas block micro-duct snap-in connector is normally used between indoor and outdoor environments to prevent air flow that may result in condensed water getting into ducts. After cable installation, the connector can be gas sealed by turning a ring on the body or by pushing the connector ends together.

 

Technical Information
Design: Micro-duct Gasblock Connector and End Stops, re-openable
Type: Above ground use
Dimensions: OD/ID Ø5/3.5 to 14/10 mm

End Caps for Micro-ducts

MPB 306 09+ and SRS 106 17

Description

The end caps are used for temporarily seal open duct ends to avoid water and dirt from entering the micro-ducts. 

 

Technical Information
Design: End caps for micro-ducts
Type: Above ground use
Dimensions: OD Ø3 to 20 mm

End Sleeves for Micro-duct Assemblies

SRS101617+

Description

Rubber end sleeves used for temporary sealing of unused micro-duct assemblies to prevent water and dust from getting into the ducts. The end sleeves are available in several versions for different types of micro-duct assemblies. 

 

Technical Information
Design: End sleeves for micro-duct assemblies
Type: Temporary use
Dimensions: OD Ø3 to 18 mm

How can we help you?